# What is the NEC code for panel clearance?

## What is the NEC code for panel clearance?

NEC code states that panels must have clearance of 36 inches in front, 30 inches to the sides, and a working area with a clearance of 6 foot 5 inches. You’ll likely need a permit to move an electric panel.

Can an electrical panel be in a kitchen?

You cannot put it over anything. You cannot put it next to anything. There must a clear space in front of the panel for an electrician to stand. The space must be kept clear for at least 3 feet in front of the panel, and for 30 inches left to right in front of the panel.

What is the minimum safe distance items can be stored next to an electrical panel?

The clear working space in front of an electrical panel (or piece of electrical equipment) must be: 2 1/2 feet if the electrical equipment was built before April 16, 1981. 3 feet when the nominal voltage is between 0 and 150 volts. 3 to 4 feet when the nominal voltage is between 151 and 600 volts.

### Are electrical panels required to have 36 inches clearance in front of panel?

A: According to NFPA 70-2011, article 110.26, a minimum of 36 inches clearance is required in front of all electrical equipment, including controls and panels, extending from the floor to a height of 6 foot 6 inches or the height of the equipment whichever is higher.

What clearance is required around electrical panels?

three feet
For equipment operating at 600 volts, nominal or less to ground, electrical panels must have a minimum of three feet of clearance in front of the panel and a minimum clearance width of 2.5 feet or the width of the equipment, whichever is greater.

How much space should be between panels?

Working Space around Indoor Panel/Circuit Board (NES 110.34)

Voltage Exposed live parts to Not live parts (or grounded parts) Exposed live parts on both sides
9.0 KV to 25 KV 1.5 Meter (5 Ft) 2.5 Meter (8 Ft)
25 KV to 75 KV 1.8 Meter (6 Ft) 3.0 Meter (10 Ft)
Above 75 KV 2.5 Meter (8 Ft) 3.7 Meter (12 Ft)

#### How much space is needed around an electrical panel?

3 feet
The space around electrical equipment should always be clear to be on the safe side. There should be at least 3 feet of space in front of equipment with a 30 inch width as well as 612 feet of headroom space.

How do I hide my kitchen electrical panel?

Strategically placed artwork, framed message boards, or a weaving or tapestry are all viable options for covering up obtrusive electrical eyesores. HGTV suggests inserting child proof safety plugs into unused outlets before covering with artwork.

What is the minimum width of the working space required at an electrical panel that is 24 wide?

wide that contains over current devices, switching devices, or control devices, there shall be one entrance to an egress from the required working space not less than 610mm (24 in.) wide and 2.0m (6½ ft.) high at each end of the working space.

## Can I put something in front of my electrical panel?

Just don’t put anything heavy or unwieldy in front of the panel, Mr. Wismer added. Or “you’ll have to get those Magic Sliders they show on TV for sliding the furniture around.”

Can an electrical panel be in a walk in closet?

The short, safest and most efficient answer to this question is yes. According to the national code, with relation to electrical panels in closets: NEC 240.24D Overcurrent devices shall not be located in the vicinity of easily ignitable materials, such as a clothes closet.

How close can an electrical panel be to a corner?

For example, California’s state building code requires a minimum clearance of 30 inches horizontally in front of an electrical panel. This means you cannot place an electrical panel close to a corner if another wall, fixture or piece of furniture is within 30 inches of it.